Subject / Started by | Replies / Views | Last post | ||
---|---|---|---|---|
Chainsaw question
Started by jay |
9 Replies
2303 Views |
March 30, 2021, 07:15:46 PM by Roger Groom |
||
Graduate short bed lathe advice on VS
Started by jay |
10 Replies
9701 Views |
April 15, 2013, 10:08:08 PM by Haggy |
||
Simon Hope Easy arm hollowing jig
Started by Tim Pettigrew |
7 Replies
3280 Views |
October 12, 2018, 10:27:46 PM by Tim Pettigrew |
||
1/2" Bowl Gouge Recommendations
Started by howlingbaboon |
5 Replies
2872 Views |
July 16, 2017, 02:53:33 PM by bernuk1 |
||
2 part epoxy glue
Started by Flame |
6 Replies
1255 Views |
February 14, 2021, 04:29:38 PM by Paul Hannaby |
||
25mm plug cutters
Started by malcy |
4 Replies
4922 Views |
December 27, 2014, 07:00:11 PM by seventhdevil |
||
3M TRIZACT Abrasive Belts
Started by Bill21 |
3 Replies
1242 Views |
March 22, 2022, 01:19:39 PM by julcle |
||
40 : 40 freehand grind
Started by Haggy |
7 Replies
6396 Views |
June 23, 2015, 08:54:37 PM by Haggy |
||
45 degree Spindle Gouge
Started by Bryan Milham |
3 Replies
3692 Views |
January 08, 2013, 05:07:47 PM by Bryan Milham |
||
A light bulb moment
Started by The Bowler Hatted Turner |
2 Replies
3476 Views |
November 06, 2013, 08:24:12 PM by burywoodturners |
||
A new lathe
Started by Oscar98 |
4 Replies
1160 Views |
November 27, 2020, 10:57:31 AM by Gregmcateer |
||
a source of spindle turning blanks?
Started by seventhdevil |
2 Replies
991 Views |
May 01, 2022, 12:53:34 PM by MelanieS |
||
Abranet Mirka's Revolution in sanding
Started by southern filters ltd |
6 Replies
5321 Views |
December 14, 2012, 04:22:37 PM by southern filters ltd |
||
10 Replies
3911 Views |
August 04, 2017, 09:22:51 PM by howlingbaboon |
|||
Adjustable grinder sharpening jigs
Started by Terry Miller |
0 Replies
3004 Views |
January 09, 2013, 09:44:19 AM by Terry Miller |
||
29 Replies
13194 Views |
October 12, 2016, 10:33:52 AM by Lazurus |
|||
Advice on buying new lathe
Started by Dean V |
10 Replies
5723 Views |
October 29, 2019, 03:38:28 PM by Lazurus |
||
Advice on secondhand Nutool lathe
Started by GeordieTurner |
3 Replies
5713 Views |
February 08, 2019, 10:38:45 AM by Derwent Woodturning club |
||
Affordable Carbon
Started by Graham |
6 Replies
5300 Views |
March 02, 2016, 10:50:18 AM by steve w |
||
Air Brushing
Started by John D Smith |
14 Replies
9093 Views |
April 12, 2012, 12:58:56 PM by John D Smith |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll