Author Topic: Oak burr hollow (very) form!  (Read 3469 times)

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Oak burr hollow (very) form!
« on: July 17, 2019, 09:07:57 AM »
This vase/form stands 8" high and is approximately 4" wide at it's widest point... or, rather, what would be it's widest point if it was actually round. As I'm sure you'll all appreciate this was a bit of a challenge sanding-wise but I'm delighted to say I still have all digits intact after the turning :)
« Last Edit: July 17, 2019, 09:11:44 AM by Motley Dog »

Offline bodrighywood

  • platinum
  • *****
  • Posts: 3631
    • Bodrighy Wood
Re: Oak burr hollow (very) form!
« Reply #1 on: July 17, 2019, 09:13:53 AM »
Big yes from me on this one. Brings a whole new meaning to 'natural edge' LOL.

Pete
Turners don't make mistakes, they have design opportunities

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Re: Oak burr hollow (very) form!
« Reply #2 on: July 17, 2019, 09:24:28 AM »
Big yes from me on this one. Brings a whole new meaning to 'natural edge' LOL.

Pete

 :) :) Cheers Pete

Offline John Plater

  • gold
  • ****
  • Posts: 295
Re: Oak burr hollow (very) form!
« Reply #3 on: July 17, 2019, 09:56:57 AM »
I like this one, shows off the markings really well. I do quite a few of this type of form, and find that they are popular with customers "who like their wood". Sanding for me is never an issue, I power sand with the piece held stationery. Maybe it takes a bit longer but the quality is more easily controlled.
Nice one !
ATB John
If I had a better lathe, I would be able to show my ineptitude more effectively.

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Re: Oak burr hollow (very) form!
« Reply #4 on: July 17, 2019, 11:59:06 AM »
I like this one, shows off the markings really well. I do quite a few of this type of form, and find that they are popular with customers "who like their wood". Sanding for me is never an issue, I power sand with the piece held stationery. Maybe it takes a bit longer but the quality is more easily controlled.
Nice one !
ATB John

Cheers John. I did power sand the outside but the inside was impossible... even stationary. Must get a long-necked sander!!
Richard

Offline Duncan A

  • bronze
  • ***
  • Posts: 175
Re: Oak burr hollow (very) form!
« Reply #5 on: July 17, 2019, 05:17:48 PM »
Wow, I really like that, but not sure I'd attempt it myself.
Definitely one to keep in mind for the future though.
Duncan

Offline Wood spinner

  • platinum
  • *****
  • Posts: 727
Re: Oak burr hollow (very) form!
« Reply #6 on: July 17, 2019, 07:31:15 PM »
I like this a lot , not a practical piece more ornamental , are the cracks filled ?

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Re: Oak burr hollow (very) form!
« Reply #7 on: July 18, 2019, 04:37:11 PM »
I like this a lot , not a practical piece more ornamental , are the cracks filled ?

Thanks Woodspinner. Yep - the cracks are filled with coffee grounds... used... obviously... I had to drink lots to keep me awake during the sanding!

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Re: Oak burr hollow (very) form!
« Reply #8 on: July 18, 2019, 04:39:28 PM »
Wow, I really like that, but not sure I'd attempt it myself.
Definitely one to keep in mind for the future though.
Duncan

Thanks Duncan. Yep, it was a bit of a health and safety challenge! All fingers still attached though... thankfully.

Offline John Plater

  • gold
  • ****
  • Posts: 295
Re: Oak burr hollow (very) form!
« Reply #9 on: July 19, 2019, 06:58:37 PM »
"Cheers John. I did power sand the outside but the inside was impossible... even stationary. Must get a long-necked sander!!"

I have an electric drill with a 90 angled head and use the 50mm hook and eye foam backed pads. If the diameter is too small for that set up I use a regular drill with an extended chuck and the Kirjes Bowl Sander. (Woodturning Magazine issue 333 page 95)  ;)
ATB John
If I had a better lathe, I would be able to show my ineptitude more effectively.

Offline Bryan Milham

  • Administrator
  • platinum
  • *****
  • Posts: 4500
  • I’ve had my patience tested; I’m negative
Re: Oak burr hollow (very) form!
« Reply #10 on: July 20, 2019, 09:56:25 PM »
It's amazing how all that air can hold a little piece of wood together! Pleased to see you can still add up to 10.

But on a serious note it is a lovely piece of work and very well done.

Oh Lord, Lead me not into temptation…

...Oh who am I kidding, follow me, I know a shortcut!

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Re: Oak burr hollow (very) form!
« Reply #11 on: July 22, 2019, 08:21:07 AM »
"Cheers John. I did power sand the outside but the inside was impossible... even stationary. Must get a long-necked sander!!"

I have an electric drill with a 90 angled head and use the 50mm hook and eye foam backed pads. If the diameter is too small for that set up I use a regular drill with an extended chuck and the Kirjes Bowl Sander. (Woodturning Magazine issue 333 page 95)  ;)
ATB John

Brilliant! Thanks John. I'll have a look.

Offline Motley Dog

  • iron
  • *
  • Posts: 28
    • Motley Dog Woodturning
Re: Oak burr hollow (very) form!
« Reply #12 on: July 22, 2019, 08:22:28 AM »
It's amazing how all that air can hold a little piece of wood together! Pleased to see you can still add up to 10.

But on a serious note it is a lovely piece of work and very well done.

 :D Ha ha! Thank you.